[Federal Register Volume 84, Number 69 (Wednesday, April 10, 2019)]
[Notices]
[Pages 14412-14420]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-07040]
-----------------------------------------------------------------------
DEPARTMENT OF LABOR
Occupational Safety and Health Administration
[Docket No. OSHA-2013-0012]
Proposed Modification to the List of Appropriate NRTL Program
Test Standards and the Scopes of Recognition of Several NRTLs
AGENCY: Occupational Safety and Health Administration (OSHA), Labor.
ACTION: Notice.
-----------------------------------------------------------------------
SUMMARY: In this notice, OSHA proposes to: (1) Add new test standards
to the Nationally Recognized Testing Laboratories (NRTL) Program's list
of appropriate test standards; (2) delete or replace several test
standards from the NRTL Program's list of appropriate test standards;
and (3) update the scope of recognition of several NRTLs.
DATES: Submit comments, information, and documents in response to this
notice, or request for an extension of time to make a submission, on or
before May 10, 2019.
ADDRESSES: Submit comments by any of the following methods:
Electronically: You may submit comments and attachments
electronically at: https://www.regulations.gov, which is the Federal
eRulemaking Portal. Follow the instructions online for submitting
comments.
Facsimile: If your comments, including attachments, are not longer
than 10 pages, you may fax them to the OSHA Docket Office at (202) 693-
1648.
Mail, hand delivery, express mail, messenger, or courier service:
When using this method, you must submit a copy of your comments and
attachments to the OSHA Docket Office, Docket No. OSHA-2013-0012,
Occupational Safety and Health Administration, U.S. Department of
Labor, Room N-3653, 200 Constitution Avenue NW, Washington, DC 20210.
Deliveries (hand, express mail, messenger, and courier service) are
accepted during the Docket Office's normal business hours, 10:00 a.m.
to 3:00 p.m., ET.
Instructions: All submissions must include the agency name and the
OSHA docket number (OSHA-2013-0012). OSHA places comments and other
materials, including any personal information, in the public docket
without revision, and these materials will be available online at
http://www.regulations.gov. Therefore, the agency cautions commenters
about submitting statements they do not want made available to the
public, or submitting comments that contain personal information
(either about themselves or others) such as Social Security Numbers,
birth dates, and medical data.
Docket: To read or download comments or other material in the
docket, go to https://www.regulations.gov or the OSHA Docket Office at
the above address. All documents in the docket (including this Federal
Register notice) are listed in the https://www.regulations.gov index;
however, some information (e.g., copyrighted material) is not publicly
available to read or download through the website. All submissions,
including copyrighted material, are available for inspection at the
OSHA Docket Office.
Extension of comment period: Submit requests for an extension of
the comment period on or before April 25, 2019 to the Office of
Technical Programs and Coordination Activities, Directorate of
Technical Support and Emergency Management, Occupational Safety and
Health Administration, U.S. Department of Labor, 200 Constitution
Avenue NW, Room N-3653, Washington, DC 20210, or by fax to (202) 693-
1644.
FOR FURTHER INFORMATION CONTACT: Information regarding this notice is
available from the following sources:
Press inquiries: Contact Mr. Frank Meilinger, Director, OSHA Office
of Communications; telephone: (202) 693-1999; email:
meilinger.francis2@dol.gov.
General and technical information: Contact Mr. Kevin Robinson,
Director, Office of Technical Programs and Coordination Activities,
Directorate of Technical Support and Emergency Management, Occupational
Safety and Health Administration; telephone: (202) 693-2110 or email:
robinson.kevin@dol.gov. OSHA's web page includes information about the
NRTL Program (see http://www.osha.gov/dts/otpca/nrtl/index.html).
SUPPLEMENTARY INFORMATION:
I. Background
The NRTL Program recognizes organizations that provide product-
safety testing and certification services to manufacturers. These
organizations
perform testing and certification for purposes of the program, to U.S.
consensus-based product-safety test standards. The products covered by
the NRTL Program consist of those items for which OSHA safety standards
require ``certification'' by a NRTL. The requirements affect electrical
products and 38 other types of products. OSHA does not develop or issue
these test standards, but generally relies on standards development
organizations (SDO), which develop and maintain the standards using a
method that provides input and consideration of views of industry
groups, experts, users, consumers, governmental authorities, and others
having broad experience in the safety field involved.
Addition of New Test Standards to the NRTL List of Appropriate Test
Standards
Periodically, OSHA will add new test standards to the NRTL list of
appropriate test standards following an evaluation of the test standard
document. To qualify as an appropriate test standard, the agency
evaluates the document to (1) verify it represents a product category
for which OSHA requires certification by a NRTL, (2) verify the
document represents an end product and not a component, and (3) verify
the document defines safety test specifications (not installation or
operational performance specifications). OSHA becomes aware of new test
standards through various avenues. For example, OSHA may become aware
of new test standards by: (1) Monitoring notifications issued by
certain SDO; (2) reviewing applications by NRTLs or applicants seeking
recognition to include a new test standard in their scopes of
recognition; and (3) obtaining notification from manufacturers,
manufacturing organizations, government agencies, or other parties that
a new test standard may be appropriate to add to the list of
appropriate standards. OSHA may determine to include a new test
standard in the list, for example, if the test standard is for a
particular type of product that another test standard also covers,
addresses a type of product that no standard previously covered, or is
otherwise new to the NRTL Program.
SDO Deletion and Replacement of Test Standards
The NRTL Program regulations require that appropriate test
standards be maintained and current (29 CFR 1910.7(c)). A test standard
withdrawn by a standards development organization is no longer
considered an appropriate test standard (Directive, App. C.XIV.B). It
is OSHA's policy to remove recognition of withdrawn test standards by
issuing a correction notice in the Federal Register for all NRTLs
recognized for the withdrawn test standards. However, SDOs frequently
will designate a replacement standard for withdrawn standards. OSHA
will recognize a NRTL for an appropriate replacement test standard if
the NRTL has the requisite testing and evaluation capability for the
replacement test standard.
One method that NRTLs may use to show such capability involves an
analysis to determine whether any testing and evaluation requirements
of existing test standards in a NRTL's scope are comparable (i.e., are
completely or substantially identical) to the requirements in the
replacement test standard. If OSHA's analysis shows the replacement
test standard does not require additional or different technical
capability than an existing test standard(s), the replacement test
standard is comparable to the existing test standard(s), then OSHA can
add the replacement test standard to affected NRTLs' scopes of
recognition. If OSHA's analysis shows the replacement test standard
requires an additional or different technical capability, or the
replacement test standard is not comparable to any existing test
standards, each affected NRTL seeking to have OSHA add the replacement
test standard to the NRTL's scope of recognition must provide
information to OSHA that demonstrates technical capability.
Other Reasons for Removal of Test Standards From the NRTL List of
Appropriate Test Standards
OSHA may choose to remove a test standard from the NRTL list of
appropriate test standards based on an internal review in which NRTL
Program staff review the NRTL list of appropriate test standards to
determine if the test standards conform to the definition of an
appropriate test standard defined in NRTL Program regulations and
policy. There are several reasons for removing a test standard based on
this review. First, a document that provides the methodology for a
single test is a test method rather than an appropriate test standard
(29 CFR 1910.7(c)). As stated above, a test standard must specify the
safety requirements for a specific type of product(s). A test method,
however, is a ``specified technical procedure for performing a test''
(Directive, App. B). As such, a test method is not an appropriate test
standard. While a NRTL may use a test method to determine if certain
safety requirements are met, a test method is not itself a safety
requirement for a specific product category.
Second, a document that focuses primarily on usage, installation,
or maintenance requirements would also not be considered an appropriate
test standard (Directive, App. D.IV.B). In some cases, however, a
document may also provide safety test specifications in addition to
usage, installation, and maintenance requirements. In such cases, the
document would be retained as an appropriate test standard based on the
safety test specifications.
Finally, a document may not be considered an appropriate test
standard if the document covers products for which OSHA does not
require testing and certification (Directive, App. D.IV.A). Similarly,
a document that covers electrical product components would not be
considered an appropriate test standard. These documents apply to types
of components that have limitation(s) or condition(s) on their use,
which are not appropriate for use as end-use products. These documents
also specify that these types of components are for use only as part of
an end-use product. NRTLs, however, evaluate such components only in
the context of evaluating whether end-use products requiring NRTL
approval are safe for use in the workplace. Testing such components
alone would not indicate that the end-use products containing the
components are safe for use. Accordingly, as a matter of policy, OSHA
considers that documents covering such components are not appropriate
test standards under the NRTL Program. OSHA notes, however, that it is
not proposing to delete from NRTLs' scopes of recognition any test
standards covering end-use products that contain such components.
In addition, OSHA notes that, to conform to a test standard
covering an end-use product, a NRTL must still determine that the
components in the product comply with the components' specific test
standards. In making this determination, NRTLs may test the components
themselves, or accept the testing of a qualified testing organization
that a given component conforms to the particular test standard. OSHA
reviews each NRTL's procedures to determine which approach the NRTL
will use to address components, and reviews the end-use product testing
to verify the NRTL appropriately addresses that product's components.
II. Proposal To Remove Test Standards to the NRTL Program's List of
Appropriate Test Standards
In this notice, OSHA proposes to delete several withdrawn and
deleted test standards from the NRTL Program's list of appropriate test
standards. OSHA proposes to incorporate into the NRTL Program's list of
appropriate test standards replacement test standards for some of the
withdrawn and deleted test standards.
Table 1 lists the test standards that OSHA proposes to delete from
the NRTL Program's List of Appropriate Test Standards, as well as an
abbreviated rationale for OSHA's proposed action. Additionally, Table 1
lists corresponding replacement test standards that OSHA proposes to
incorporate into the NRTL Program's List of Appropriate Test Standards
(when applicable). OSHA seeks comment on this preliminary
determination.
OSHA notes that Table 1 lists the subject test standards and the
proposed action with regard to each of these test standards without
indicating how the proposed action will affect individual NRTLs.
Section IV of this notice discusses how the proposed action will affect
individual NRTLs.
Table 1--Test Standards OSHA Is Proposing To Remove From NRTL Program's
List of Appropriate Test Standards
------------------------------------------------------------------------
Proposed
Proposed deleted test Test standard Reason for replacement
standard title deletion standard(s)
------------------------------------------------------------------------
ANSI C37.44.......... Distribution Withdrawn...... None.
Oil Cutouts
and Fuse Links.
IEEE C37.09.......... Standard Test Withdrawn...... None.
Procedure for
High-Voltage
Circuit
Breakers Rated
on a
Symmetrical
Current Basis.
IEEE C37.29.......... Low-Voltage AC Withdrawn...... None.
Power Circuit
Protectors
Used in
Enclosures.
IEEE C37.45.......... Distribution Withdrawn...... None.
Enclosed
Single-Pole
Air Switches.
NEMA C37.52.......... Low-Voltage AC Withdrawn...... None.
Power Circuit
Protectors
Used in
Enclosures--Te
st Procedures.
IEEE C37.53.......... High-Voltage Withdrawn...... None.
Current Motor-
Starter Fuses--
Conformance
Test
Procedures.
ISA 82.02.01......... Electric and Withdrawn...... None.
Electronic
Test,
Measuring,
Controlling
and Related
Equipment:
General
Requirement.
UL 1093.............. Halogenated Withdrawn...... None.
Agent Fire
Extinguishers.
UL 1244.............. Electrical and Withdrawn...... None.
Electronic
Measuring and
Testing
Equipment.
UL 1448.............. Electric Hedge Withdrawn and UL 60745-2-15
Trimmers. replaced. Particular
Requirements
for Hedge
Trimmers.
ISA 60079-2.......... Explosive Withdrawn and UL 60079-2
Atmospheres--P replaced. Explosive
art 2: Atmospheres--P
Equipment art 2:
Protection by Protection by
Pressurized Pressurized
Enclosures Enclosures
``p''. ``p''.
ISA 60079-5.......... Explosive Withdrawn and UL 60079-5
Atmospheres--P replaced. Explosive
art 5: Atmospheres--P
Equipment art 5:
Protection by Equipment
Powder Filling Protection by
``q''. Powder Filling
``q''.
ISA 60079-18......... Explosive Withdrawn and UL 60079-18
Atmospheres--P replaced. Explosive
art 18: Atmospheres--P
Equipment art 18:
Protection by Equipment
Encapsulation Protection by
``m''. Encapsulation
``m''.
ISA 60079-26......... Explosive Withdrawn and UL 60079-26
Atmospheres--P replaced. Explosive
art 26: Atmospheres--P
Equipment for art 26:
Use in Class Equipment for
I, Zone 0 Use in Class
Hazardous I, Zone 0
(Classified) Hazardous
Locations. (Classified)
Locations.
UL 745-1............. Portable Withdrawn...... None.
Electric Tools.
UL 745-2............. Particular Withdrawn...... None.
Requirements
of Drills.
UL 745-2-3........... Particular Withdrawn...... None.
Requirements
for Grinders,
Polishers and
Disk-Type
Sanders.
UL 745-2-17.......... Particular Withdrawn...... None.
Requirements
for Circular
Saws and
Circular
Knives.
UL 745-2-36.......... Particular Withdrawn...... None.
Requirements
for Hand Motor
Tools.
UL 745-2-37.......... Particular Withdrawn...... None.
Requirements
for Plate
Jointers.
UL 61010A-1.......... Electrical Withdrawn and UL 61010-1
Equipment for replaced. Electrical
Laboratory Equipment for
Use; Part 1: Measurement,
General Control and
Requirements. Laboratory
Use; Part 1:
General
Requirements.
UL 61010A-2-010...... Electrical Withdrawn and UL 61010-2-010
Equipment for replaced. Electrical
Laboratory Equipment for
Use; Part 2: Measurement,
Particular Control and
Requirements Laboratory
for the Use--Part 2-
Heating of 010:
Materials. Particular
Requirements
for Laboratory
Equipment for
the Heating of
Materials.
UL 61010A-2-020...... Electrical Withdrawn and UL 61010-2-020
Equipment for replaced. Electrical
Laboratory Equipment for
Use; Part 2: Measurement,
Particular Control, and
Requirements Laboratory
for Laboratory Use--Part 2-
Centrifuges. 020:
Particular
Requirements
for Laboratory
Centrifuges.
UL 61010A-2-041...... Electrical Withdrawn and UL 61010-1 (no
Equipment for replaced. direct
Laboratory replacement).
Use: Part 2:
Particular
Requirements
for Autoclaves
Using Steam
for the
Treatment of
Medical
Materials for
Laboratory
Purposes.
UL 61010A-2-051...... Electrical Withdrawn and UL 61010-2-051
Equipment for replaced. Electrical
Laboratory Equipment for
Use; Part 2: Measurement,
Particular Control and
Requirements Laboratory
for Laboratory Use--Part 2-
Equipment 051:
Mixing and Particular
Stirring. Requirements
for Laboratory
Equipment for
Mixing and
Stirring.
UL 61010A-2-061...... Electrical Withdrawn and UL 61010-2-061
Equipment for replaced. Electrical
Laboratory Equipment for
Use: Part 2: Measurement,
Particular Control and
Requirements Laboratory
for Laboratory Use--Part 2-
Atomic 061:
Spectrometers Particular
with Thermal Requirements
Atomization for Laboratory
and Ionization. Atomic
Spectrometers
with Thermal
Atomization
and
Ionization.
UL 61010B-1.......... Electrical Withdrawn and UL 61010-1
Measuring and replaced. Electrical
Test Equipment for
Equipment; Measurement,
Part 1: Control and
General Laboratory
Requirements. Use; Part 1:
General
Requirements.
UL 61010B-2-031...... Electrical Withdrawn and UL 61010-1 (no
Equipment for replaced. direct
Measurement, replacement).
Control and
Laboratory
Use: Part 2:
Particular
Requirements
for Hand-Held
Probe
Assemblies for
Electrical
Measurement
and Test.
UL 61010C-1.......... Process Control Withdrawn and UL 61010-1
Equipment. replaced. Electrical
Equipment for
Measurement,
Control and
Laboratory
Use; Part 1:
General
Requirements.
------------------------------------------------------------------------
III. Proposed Modifications to Affected NRTLs' Scopes of Recognition
In this notice, OSHA additionally proposes to update the scopes of
recognition of several NRTLs with a replacement for the test standard
OSHA proposes to remove. The tables in this section (Table 2 thru Table
9) list, for each affected NRTL, the test standard(s) that OSHA
proposes to remove from the scope of recognition of the NRTL along with
the proposed replacement test standard (if any).
OSHA seeks comment on whether its proposed deletion and replacement
are appropriate, and whether individual tables omit any appropriate
replacement test standard that is comparable to a withdrawn test
standard. If OSHA determines that it omitted any appropriate
replacement test standard that is comparable to a withdrawn test
standard, it will, in its final determination, incorporate that
replacement test standard into the scope of recognition of each
affected NRTL.
Comments should consist of pertinent written documents and
exhibits. Commenters needing more time to comment must submit a request
in writing, stating the reasons for the request, by the due date for
comments. OSHA will limit any extension to 10 days unless the requester
justifies a longer time period. OSHA may deny a request for an
extension if it is not adequately justified.
Table 2--Test Standards OSHA Proposes To Remove From the Scope of
Recognition of the Canadian Standards Association
------------------------------------------------------------------------
Proposed replacement
Proposed test standard to be Reason for proposed test standard(s) (if
removed removal applicable)
------------------------------------------------------------------------
UL 61010A-2-020--Electrical Standard withdrawn UL 61010-2-020--
Equipment for Laboratory by Standards Standard for Safety
Use; Part 2: Particular Organization. Requirements for
Requirements for Laboratory Electrical
Equipment for Laboratory Equipment for
Centrifuges. Laboratory Use;
Part 2-020:
Particular
Requirements for
Laboratory
Equipment for
Laboratory
Centrifuges.
IEEE C37.09 Standard Test Withdrawn........... None.
Procedure for AC High-
Voltage Circuit Breakers
Rated on a Symmetrical
Current Basis.
IEEE C37.29 Low-Voltage AC Withdrawn........... None.
Power Circuit Protectors
Used in Enclosures.
IEEE C37.45 Distribution Withdrawn........... None.
Enclosed Single-Pole Air
Switches.
NEMA C37.52 Low-Voltage AC Withdrawn........... None.
Power Circuit Protectors
Used in Enclosures--Test
Procedures.
ISA 82.02.01 Electric and Withdrawn........... None.
Electronic Test, Measuring,
Controlling and Related
Equipment: General
Requirement.
UL 1244..................... Withdrawn........... None.
UL 1448..................... Withdrawn and UL 60745-2-15
Replaced. Particular
Requirements for
Hedge Trimmers.
ISA 60079-2 Explosive Withdrawn and UL 60079-2 Explosive
Atmospheres--Part 2: replaced. Atmospheres--Part
Equipment Protection by 2: Equipment
Pressurized Enclosures Protection by
``p''. Pressurized
Enclosures ``p''.
ISA 60079-5 Explosive Withdrawn and UL 60079-5 Explosive
Atmospheres--Part 5: replaced. Atmospheres--Part
Equipment Protection by 5: Equipment
Power Filling ``q''. Protection by
Powder Filling
``q''.
ISA 60079-18 Explosive Withdrawn and UL 60079-18
Atmospheres--Part 18: replaced. Explosive
Equipment Protection by Atmospheres--Part
Encapsulation ``m''. 18: Equipment
Protection by
Encapsulation
``m''.
ISA 60079-26 Explosive Withdrawn and UL 60079-26
Atmospheres--Part 26: replaced. Explosive
Equipment for Use in Class Atmospheres--Part
I, Zone 0 Hazardous 26: Equipment for
(Classified) Locations. Use in Class I,
Zone 0 Hazardous
(Classified)
Locations.
UL 745-1 Portable Electric Withdrawn........... None.
Tools.
UL 745-2-1 Particular Withdrawn........... None.
Requirements of Drills.
UL 745-2-5 Particular Withdrawn........... None.
Requirements for Circular
Saws and Circular Knives.
UL 745-2-17 Particular Withdrawn........... None.
Requirements for Routers
and Trimmers.
UL 745-2-36 Particular Withdrawn........... None.
Requirements for Hand Motor
Tools.
UL 745-2-37 Particular Withdrawn........... None.
Requirements for Plate
Jointers.
UL 61010A-1 Electrical Withdrawn and UL 61010-1
Equipment for Laboratory replaced. Electrical
Use; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
UL 61010A-2-010 Electrical Withdrawn and UL 61010-2-010
Equipment for Laboratory replaced. Electrical
Use; Part 2: Particular Equipment for
Requirements for the Measurement,
Heating of Materials. Control and
Laboratory Use--
Part 2-010:
Particular
Requirements for
Laboratory
Equipment for the
Heating of
Materials.
UL 61010A-2-020 Electrical Withdrawn and UL 61010-2-020
Equipment for Laboratory replaced. Electrical
Use; Part 2: Particular Equipment for
Requirements for Laboratory Measurement,
Centrifuges. Control, and
Laboratory Use--
Part 2-020:
Particular
Requirements for
Laboratory
Centrifuges.
UL 61010A-2-041 Electrical Withdrawn and UL 61010-1 (no
Equipment for Laboratory replaced. direct
Use: Part 2: Particular replacement).
Requirements for Autoclaves
Using Steam for the
Treatment of Medical
Materials for Laboratory
Purposes.
UL 61010A-2-051 Electrical Withdrawn and UL 61010-2-051
Equipment for Laboratory replaced. Electrical
Use; Part 2: Particular Equipment for
Requirements for Laboratory Measurement,
Equipment Mixing and Control and
Stirring. Laboratory Use--
Part 2-051:
Particular
Requirements for
Laboratory
Equipment for
Mixing and
Stirring.
UL 61010A-2-061 Electrical Withdrawn and UL 61010-2-061
Equipment for Laboratory replaced. Electrical
Use: Part 2: Particular Equipment for
Requirements for Laboratory Measurement,
Atomic Spectrometers with Control and
Thermal Atomization and Laboratory Use--
Ionization. Part 2-061:
Particular
Requirements for
Laboratory Atomic
Spectrometers with
Thermal Atomization
and Ionization.
UL 61010B-1 Electrical Withdrawn and UL 61010-1
Measuring and Test replaced. Electrical
Equipment; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
UL 61010B-2-031 Electrical Withdrawn and UL 61010-1 (no
Equipment for Measurement, replaced. direct
Control and Laboratory Use: replacement).
Part 2: Particular
Requirements for Hand-Held
Probe Assemblies for
Electrical Measurement and
Test.
UL 61010C-1 Process Control Withdrawn and UL 61010-1
Equipment. replaced. Electrical
Equipment for
Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
------------------------------------------------------------------------
Table 3--Test Standard OSHA Proposes To Remove From the Scope of
Recognition of FM Approvals LLC
------------------------------------------------------------------------
Proposed replacement
Proposed test standard to be Reason for proposed test standard(s) (if
removed removal applicable)
------------------------------------------------------------------------
UL 1093..................... Withdrawn........... None.
ISA 82.02.01 Electric and Withdrawn........... None.
Electronic Test, Measuring,
Controlling and Related
Equipment: General
Requirement.
UL 61010A-1 Electrical Withdrawn and UL 61010-1
Equipment for Laboratory replaced. Electrical
Use; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
UL 61010B-1 Electrical Withdrawn and UL 61010-1
Measuring and Test replaced. Electrical
Equipment; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
------------------------------------------------------------------------
Table 4--Test Standard OSHA Proposes To Remove From the Scope of
Recognition of Intertek Testing Services, NA
------------------------------------------------------------------------
Proposed replacement
Proposed test standard to be Reason for proposed test standard(s) (if
removed removal applicable)
------------------------------------------------------------------------
UL 61010A-2-020--Electrical Standard withdrawn UL 61010-2-020--
Equipment for Laboratory by Standards Standard for Safety
Use; Part 2: Particular Organization. Requirements for
Requirements for Laboratory Electrical
Equipment for Laboratory Equipment for
Centrifuges. Laboratory Use;
Part 2-020:
Particular
Requirements for
Laboratory
Centrifuges.
IEEE C37.29 Low-Voltage AC Withdrawn........... None.
Power Circuit Protectors
Used in Enclosures.
ISA 82.02.01 Electric and Withdrawn........... None.
Electronic Test, Measuring,
Controlling and Related
Equipment: General
Requirement.
UL 1093 Halogenated Agent Withdrawn........... None.
Fire Extinguishers.
UL 1244 Electrical and Withdrawn........... None.
Electronic Measuring and
Testing Equipment.
UL 1448 Electric Hedge Withdrawn and UL 60745-2-15
Trimmers. Replaced. Particular
Requirements for
Hedge Trimmers.
ISA 60079-2 Explosive Withdrawn and UL 60079-2 Explosive
Atmospheres--Part 2: replaced. Atmospheres--Part
Equipment Protection by 2: Equipment
Pressurized Enclosures Protection by
``p''. Pressurized
Enclosures ``p''.
ISA 60079-5 Explosive Withdrawn and UL 60079-5 Explosive
Atmospheres--Part 5: replaced. Atmospheres--Part
Equipment Protection by 5: Equipment
Power Filling ``q''. Protection by
Powder Filling
``q''.
ISA 60079-18 Explosive Withdrawn and UL 60079-18
Atmospheres--Part 18: replaced. Explosive
Equipment Protection by Atmospheres--Part
Encapsulation ``m''. 18: Equipment
Protection by
Encapsulation
``m''.
ISA 60079-26 Explosive Withdrawn and UL 60079-26
Atmospheres--Part 26: replaced. Explosive
Equipment for Use in Class Atmospheres--Part
I, Zone 0 Hazardous 26: Equipment for
(Classified) Locations. Use in Class I,
Zone 0 Hazardous
(Classified)
Locations.
UL 745-1 Portable Electric Withdrawn........... None.
Tools.
UL 745-2-1 Particular Withdrawn........... None.
Requirements of Drills.
UL 745-2-5 Particular Withdrawn........... None.
Requirements for Circular
Saws and Circular Knives.
UL 745-2-17 Particular Withdrawn........... None.
Requirements for Routers
and Trimmers.
UL 745-2-36 Particular Withdrawn........... None.
Requirements for Hand Motor
Tools.
UL 745-2-37 Particular Withdrawn........... None.
Requirements for Plate
Jointers.
UL 61010A-1 Electrical Withdrawn and UL 61010-1
Equipment for Laboratory replaced. Electrical
Use; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
UL 61010A-2-010 Electrical Withdrawn and UL 61010-2-010
Equipment for Laboratory replaced. Electrical
Use; Part 2: Particular Equipment for
Requirements for the Measurement,
Heating of Materials. Control and
Laboratory Use--
Part 2-010:
Particular
Requirements for
Laboratory
Equipment for the
Heating of
Materials.
UL 61010A-2-020 Electrical Withdrawn and UL 61010-2-020
Equipment for Laboratory replaced. Electrical
Use; Part 2: Particular Equipment for
Requirements for Laboratory Measurement,
Centrifuges. Control, and
Laboratory Use--
Part 2-020:
Particular
Requirements for
Laboratory
Centrifuges.
UL 61010A-2-041 Electrical Withdrawn and UL 61010-1 (no
Equipment for Laboratory replaced. direct
Use: Part 2: Particular replacement).
Requirements for Autoclaves
Using Steam for the
Treatment of Medical
Materials for Laboratory
Purposes.
UL 61010A-2-051 Electrical Withdrawn and UL 61010-2-051
Equipment for Laboratory replaced. Electrical
Use; Part 2: Particular Equipment for
Requirements for Laboratory Measurement,
Equipment Mixing and Control and
Stirring. Laboratory Use--
Part 2-051:
Particular
Requirements for
Laboratory
Equipment for
Mixing and
Stirring.
UL 61010A-2-061 Electrical Withdrawn and UL 61010-2-061
Equipment for Laboratory replaced. Electrical
Use: Part 2: Particular Equipment for
Requirements for Laboratory Measurement,
Atomic Spectrometers with Control and
Thermal Atomization and Laboratory Use--
Ionization. Part 2-061:
Particular
Requirements for
Laboratory Atomic
Spectrometers with
Thermal Atomization
and Ionization.
UL 61010B-1 Electrical Withdrawn and UL 61010-1
Measuring and Test replaced. Electrical
Equipment; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
UL 61010B-2-031 Electrical Withdrawn and UL 61010-1 (no
Equipment for Measurement, replaced. direct
Control and Laboratory Use: replacement).
Part 2: Particular
Requirements for Hand-Held
Probe Assemblies for
Electrical Measurement and
Test.
UL 61010C-1 Process Control Withdrawn and UL 61010-1
Equipment. replaced. Electrical
Equipment for
Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
------------------------------------------------------------------------
Table 5--Test Standard OSHA Proposes To Remove From the Scope of
Recognition of MET Laboratories, Inc.
------------------------------------------------------------------------
Proposed replacement
Proposed test standard to be Reason for proposed test standard(s) (if
removed removal applicable)
------------------------------------------------------------------------
UL 1448 Electric Edge Withdrawn and UL 60745-2-15
Trimmers. Replaced. Particular
Requirements for
Hedge Trimmers.
UL 1244 Electrical and Withdrawn........... None.
Electronic Measuring and
Testing Equipment.
UL 61010A-1 Electrical Withdrawn and UL 61010-1
Equipment for Laboratory replaced. Electrical
Use; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
UL 61010B-1 Electrical Withdrawn and UL 61010-1
Measuring and Test replaced. Electrical
Equipment; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
UL 61010C-1 Process Control Withdrawn and UL 61010-1
Equipment. replaced. Electrical
Equipment for
Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
------------------------------------------------------------------------
Table 6--Test Standard OSHA Proposes To Remove From the Scope of
Recognition of TUV Rheinland of North America, Inc.
------------------------------------------------------------------------
Proposed replacement
Proposed test standard to be Reason for proposed test standard(s) (if
removed removal applicable)
------------------------------------------------------------------------
UL 1448..................... Withdrawn and UL 60745-2-15
replaced. Particular
Requirements for
Hedge Trimmers.
UL 745-1 Portable Electric Withdrawn........... None.
Tools.
UL 745-2-1 Particular Withdrawn........... None.
Requirements of Drills.
UL 745-2-5 Particular Withdrawn........... None.
Requirements for Circular
Saws and Circular Knives.
UL 745-2-17 Particular Withdrawn........... None.
Requirements for Routers
and Trimmers.
UL 745-2-36 Particular Withdrawn........... None.
Requirements for Hand Motor
Tools.
UL 745-2-37 Particular Withdrawn........... None.
Requirements for Plate
Jointers.
UL 61010A-1 Electrical Withdrawn and UL 61010-1
Equipment for Laboratory replaced. Electrical
Use; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
UL 61010B-1 Electrical Withdrawn and UL 61010-1
Measuring and Test replaced. Electrical
Equipment; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
UL 61010C-1 Process Control Withdrawn and UL 61010-1
Equipment. replaced. Electrical
Equipment for
Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
------------------------------------------------------------------------
Table 7--Test Standard OSHA Proposes To Remove From the Scope of
Recognition of TUV SUD America, Inc.
------------------------------------------------------------------------
Proposed replacement
Proposed test standard to be Reason for proposed test standard(s) (if
remove removal applicable)
------------------------------------------------------------------------
UL 61010A-2-020--Electrical Standard withdrawn UL 61010-2-020--
Equipment for Laboratory by Standards Standard for Safety
Use; Part 2: Particular Organization. Requirements for
Requirements for Laboratory Electrical
Equipment for Laboratory Equipment for
Centrifuges. Laboratory Use;
Part 2-020:
Particular
Requirements for
Laboratory
Centrifuges.
UL 1448..................... Withdrawn and UL 60745-2-15
replaced. Particular
Requirements for
Hedge Trimmers.
UL 745-1 Portable Electric Withdrawn........... None.
Tools.
UL 745-2-1 Particular Withdrawn........... None.
Requirements of Drills.
UL 745-2-5 Particular Withdrawn........... None.
Requirements for Circular
Saws and Circular Knives.
UL 745-2-17 Particular Withdrawn........... None.
Requirements for Routers
and Trimmers.
UL 745-2-36 Particular Withdrawn........... None.
Requirements for Hand Motor
Tools.
UL 745-2-37 Particular Withdrawn........... None.
Requirements for Plate
Jointers.
UL 61010A-1 Electrical Withdrawn and UL 61010-1
Equipment for Laboratory replaced. Electrical
Use; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
UL 61010A-2-010 Electrical Withdrawn and UL 61010-2-010.
Equipment for Laboratory replaced.
Use; Part 2: Particular
Requirements for the
Heating of Materials.
UL 61010A-2-020 Electrical Withdrawn and UL 61010-2-010
Equipment for Laboratory replaced. Electrical
Use; Part 2: Particular Equipment for
Requirements for Laboratory Measurement,
Centrifuges. Control and
Laboratory Use--
Part 2-010:
Particular
Requirements for
Laboratory
Equipment for the
Heating of
Materials.
UL 61010A-2-041 Electrical Withdrawn and UL 61010-1 (no
Equipment for Laboratory replaced. direct
Use: Part 2: Particular replacement).
Requirements for Autoclaves
Using Steam for the
Treatment of Medical
Materials for Laboratory
Purposes.
UL 61010A-2-051 Electrical Withdrawn and UL 61010-2-051
Equipment for Laboratory replaced. Electrical
Use; Part 2: Particular Equipment for
Requirements for Laboratory Measurement,
Equipment Mixing and Control and
Stirring. Laboratory Use--
Part 2-051:
Particular
Requirements for
Laboratory
Equipment for
Mixing and
Stirring.
UL 61010A-2-061 Electrical Withdrawn and UL 61010-2-061
Equipment for Laboratory replaced. Electrical
Use: Part 2: Particular Equipment for
Requirements for Laboratory Measurement,
Atomic Spectrometers with Control and
Thermal Atomization and Laboratory Use--
Ionization. Part 2-061:
Particular
Requirements for
Laboratory Atomic
Spectrometers with
Thermal Atomization
and Ionization.
UL 61010B-1 Electrical Withdrawn and UL 61010-1
Measuring and Test replaced. Electrical
Equipment; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
UL 61010B-2-031 Electrical Withdrawn and UL 61010-1 (no
Equipment for Measurement, replaced. direct
Control and Laboratory Use: replacement).
Part 2: Particular
Requirements for Hand-Held
Probe Assemblies for
Electrical Measurement and
Test.
------------------------------------------------------------------------
Table 8--Test Standard OSHA Proposes To Remove From the Scope of
Recognition of TUVPSG, Inc.
------------------------------------------------------------------------
Proposed replacement
Proposed test standard to be Reason for proposed test standard(s) (if
removed removal applicable)
------------------------------------------------------------------------
UL 745-1 Portable Electric Withdrawn........... None.
Tools.
UL 745-2-1 Particular Withdrawn........... None.
Requirements of Drills.
UL 745-2-5 Particular Withdrawn........... None.
Requirements for Circular
Saws and Circular Knives.
UL 745-2-17 Particular Withdrawn........... None.
Requirements for Routers
and Trimmers.
UL 745-2-36 Particular Withdrawn........... None.
Requirements for Hand Motor
Tools.
UL 745-2-37 Particular Withdrawn........... None.
Requirements for Plate
Jointers.
UL 61010A-1 Electrical Withdrawn and UL 61010-1
Equipment for Laboratory replaced. Electrical
Use; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
UL 61010A-2-010 Electrical Withdrawn and UL 61010-2-010
Equipment for Laboratory replaced. Electrical
Use; Part 2: Particular Equipment for
Requirements for the Measurement,
Heating of Materials. Control and
Laboratory Use--
Part 2-010:
Particular
Requirements for
Laboratory
Equipment for the
Heating of
Materials.
UL 61010A-2-020 Electrical Withdrawn and UL 61010-2-020
Equipment for Laboratory replaced. Electrical
Use; Part 2: Particular Equipment for
Requirements for Laboratory Measurement,
Centrifuges. Control, and
Laboratory Use--
Part 2-020:
Particular
Requirements for
Laboratory
Centrifuges.
UL 61010A-2-041 Electrical Withdrawn and UL 61010-1 (no
Equipment for Laboratory replaced. direct
Use: Part 2: Particular replacement).
Requirements for Autoclaves
Using Steam for the
Treatment of Medical
Materials for Laboratory
Purposes.
UL 61010A-2-051 Electrical Withdrawn and UL 61010-2-051
Equipment for Laboratory replaced. Electrical
Use; Part 2: Particular Equipment for
Requirements for Laboratory Measurement,
Equipment Mixing and Control and
Stirring. Laboratory Use--
Part 2-051:
Particular
Requirements for
Laboratory
Equipment for
Mixing and
Stirring.
UL 61010A-2-061 Electrical Withdrawn and UL 61010-2-061
Equipment for Laboratory replaced. Electrical
Use: Part 2: Particular Equipment for
Requirements for Laboratory Measurement,
Atomic Spectrometers with Control and
Thermal Atomization and Laboratory Use--
Ionization. Part 2-061:
Particular
Requirements for
Laboratory Atomic
Spectrometers with
Thermal Atomization
and Ionization.
UL 61010B-1 Electrical Withdrawn and UL 61010-1
Measuring and Test replaced. Electrical
Equipment; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
------------------------------------------------------------------------
Table 9--Test Standard OSHA Proposes To Remove From the Scope of
Recognition of Underwriters Laboratory, Inc.
------------------------------------------------------------------------
Proposed replacement
Proposed test standard to be Reason for proposed test standard(s) (if
removed removal applicable)
------------------------------------------------------------------------
UL 61010A-2-020--Electrical Standard withdrawn UL 61010-2-020--
Equipment for Laboratory by Standards Standard for Safety
Use; Part 2: Particular Organization. Requirements for
Requirements for Laboratory Electrical
Equipment for Laboratory Equipment for
Centrifuges. Laboratory Use;
Part 2-020:
Particular
Requirements for
Laboratory
Centrifuges.
ANSI C37.44 Distribution Oil Withdrawn........... None.
Cutouts and Fuse Links.
IEEE C37.29 Low-Voltage AC Withdrawn........... None.
Power Circuit Protectors
Used in Enclosures.
IEEE C37.45 Distribution Withdrawn........... None.
Enclosed Single-Pole Air
Switches.
IEEE C37.52 Low-Voltage AC Withdrawn........... None.
Power Circuit Protectors
Used in Enclosures--Test
Procedures.
UL 1093 Halogenated Agent Withdrawn........... None.
Fire Extinguishers.
UL 1244 Electrical and Withdrawn........... None.
Electronic Measuring and
Testing Equipment.
UL 1448 Electric Hedge Withdrawn and UL 60745-2-15
Trimmers. replaced. Particular
Requirements for
Hedge Trimmers.
ISA 60079-2 Explosive Withdrawn and UL 60079-2 Explosive
Atmospheres--Part 2: replaced. Atmospheres--Part
Equipment Protection by 2: Protection by
Pressurized Enclosures Pressurized
``p''. Enclosures ``p''.
ISA 60079-5 Explosive Withdrawn and UL 60079-5 Explosive
Atmospheres--Part 5: replaced. Atmospheres--Part
Equipment Protection by 5: Equipment
Power Filling ``q''. Protection by
Powder Filling
``q''.
ISA 60079-18 Explosive Withdrawn and UL 60079-18
Atmospheres--Part 18: replaced. Explosive
Equipment Protection by Atmospheres--Part
Encapsulation ``m''. 18: Equipment
Protection by
Encapsulation
``m''.
ISA 60079-26 Explosive Withdrawn and UL 60079-26
Atmospheres--Part 26: replaced. Explosive
Equipment for Use in Class Atmospheres--Part
I, Zone 0 Hazardous 26: Equipment for
(Classified) Locations. Use in Class I,
Zone 0 Hazardous
(Classified)
Locations.
UL 745-1 Portable Electric Withdrawn........... None.
Tools.
UL 745-2-1 Particular Withdrawn........... None.
Requirements of Drills.
UL 745-2-5 Particular Withdrawn........... None.
Requirements for Circular
Saws and Circular Knives.
UL 745-2-17 Particular Withdrawn........... None.
Requirements for Routers
and Trimmers.
UL 745-2-36 Particular Withdrawn........... None.
Requirements for Hand Motor
Tools.
UL 745-2-37 Particular Withdrawn........... None.
Requirements for Plate
Jointers.
UL 61010A-1 Electrical Withdrawn and UL 61010-1
Equipment for Laboratory replaced. Electrical
Use; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
UL 61010A-2-010 Electrical Withdrawn and UL 61010-2-010
Equipment for Laboratory replaced. Electrical
Use; Part 2: Particular Equipment for
Requirements for the Measurement,
Heating of Materials. Control and
Laboratory Use--
Part 2-010:
Particular
Requirements for
Laboratory
Equipment for the
Heating of
Materials.
UL 61010A-2-020 Electrical Withdrawn and UL 61010-2-020
Equipment for Laboratory replaced. Electrical
Use; Part 2: Particular Equipment for
Requirements for Laboratory Measurement,
Centrifuges. Control, and
Laboratory Use--
Part 2-020:
Particular
Requirements for
Laboratory
Centrifuges.
UL 61010A-2-041 Electrical Withdrawn and UL 61010-1 (no
Equipment for Laboratory replaced. direct
Use: Part 2: Particular replacement).
Requirements for Autoclaves
Using Steam for the
Treatment of Medical
Materials for Laboratory
Purposes.
UL 61010A-2-051 Electrical Withdrawn and UL 61010-2-051
Equipment for Laboratory replaced. Electrical
Use; Part 2: Particular Equipment for
Requirements for Laboratory Measurement,
Equipment Mixing and Control and
Stirring. Laboratory Use--
Part 2-051:
Particular
Requirements for
Laboratory
Equipment for
Mixing and
Stirring.
UL 61010A-2-061 Electrical Withdrawn and UL 61010-2-061
Equipment for Laboratory replaced. Electrical
Use: Part 2: Particular Equipment for
Requirements for Laboratory Measurement,
Atomic Spectrometers with Control and
Thermal Atomization and Laboratory Use--
Ionization. Part 2-061:
Particular
Requirements for
Laboratory Atomic
Spectrometers with
Thermal Atomization
and Ionization.
UL 61010B-1 Electrical Withdrawn and UL 61010-1
Measuring and Test replaced. Electrical
Equipment; Part 1: General Equipment for
Requirements. Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
UL 61010B-2-031 Electrical Withdrawn and UL 61010-1 (no
Equipment for Measurement, replaced. direct
Control and Laboratory Use: replacement).
Part 2: Particular
Requirements for Hand-Held
Probe Assemblies for
Electrical Measurement and
Test.
UL 61010C-1 Process Control Withdrawn and UL 61010-1
Equipment. replaced. Electrical
Equipment for
Measurement,
Control and
Laboratory Use;
Part 1: General
Requirements.
------------------------------------------------------------------------
To obtain or review copies of comments submitted to the docket,
contact the Docket Office, Occupational Safety and Health
Administration, U.S. Department of Labor, at the above address. These
materials will also be available online at http://www.regulations.gov
under Docket No. OSHA-2013-0012.
OSHA staff will review all comments to the docket submitted in a
timely manner and, after addressing the issues raised by these
comments, will make a recommendation to the Assistant Secretary for
Occupational Safety and Health regarding the removal of these test
standards from the NRTL Program's List of Appropriate Test Standards
and to update the scope of recognition of several NRTLs. The Assistant
Secretary will make the final decision. In making this decision, the
Assistant Secretary may undertake other proceedings prescribed in
Appendix A to 29 CFR 1910.7. OSHA will publish a public notice of this
final decision in the Federal Register.
IV. Authority and Signature
Loren Sweatt, Acting Assistant Secretary of Labor for Occupational
Safety and Health, authorized the preparation of this notice.
Accordingly, the agency is issuing this notice pursuant to 29 U.S.C.
657(g)(2)), Secretary of Labor's Order No. 1-2012 (77 FR 3912, Jan. 25,
2012), and 29 CFR 1910.7.
Signed at Washington, DC, on April 3, 2019.
Loren Sweatt,
Acting Assistant Secretary of Labor for Occupational Safety and Health.
[FR Doc. 2019-07040 Filed 4-9-19; 8:45 am]
BILLING CODE 4510-26-P
