When safeguarding metal turning equipment, the general requirements that apply to these types of machines are in OSHA's (Occupational Safety and Health Act) Code of Federal Regulations. The following is a list:

1. An Act – Public Law 91 - 596, 91st Congress, S. 2193, December 29, 1970, Duties, Section 5(a)(1)(2)(b)

2. OSHA's 29 Code of Federal Regulations, Subpart O, that an employer (user) must comply with include:

   • Section 1910.211 Definitions
   • Section 1910.212 (a) General Requirements for all Machines
   • Section 1910.213 Woodworking Machinery Requirements
   • Section 1910.215 Abrasive Wheel Machinery

   • Section 1910.219 (b)(1) Mechanical Power-Transmission Apparatus (Flywheel and Gear Covers)

3. OSHA's 29 Code of Federal Regulations, Subpart J, 1910.147 The Control of Hazardous Energy (Lockout/Tagout)

4. OSHA's 29 Code of Federal Regulations, Subpart S, Electrical, 1910.301 - 1910.399

   These publications can be acquired by contacting:

   US Department of Labor
   Occupational Safety and Health Administration
   Washington, DC 20210
   (202) 219-5257

For guidance and further clarification of the standards, please refer to the following OSHA Directives:

• 29 CFR 1910.147 - The Control of Hazardous Energy - Enforcement Policy and Inspection Procedures. CPL 02-00-147, (February 11, 2008).
• Guidelines for Point of Operation Guarding of Power Press Brakes. CPL 02-01-025 [CPL 2-1.25], (February 14, 1997).
• Abrasive Operation Using Cutoff Wheels and Masonry Saws. STD 01-12-026 [STD 1-12.26A], (September 26, 1994).
• Guarding of Three-Roller Printing Ink Mills. STD 01-12-023 [STD 1-12.23A], (July 12, 1994).
• Awareness Barriers Installed on Metal Cutting Shears. STD 01-12-025 [STD 1-12.25A], (July 12, 1994).
• Alternative Abatement Methods of 29 CFR 1910.212(a)(1) and (a)(2) As Applied to the Oil and Gas Drilling Industry. STD 01-12-028 [STD 1-12.28 CH-1], (February 14, 1983).
• Alternative Abatement Methods of 29 CFR 1910.212(a)(1) and (a)(2) As Applied to the Oil and Gas Drilling Industry. STD 01-12-028 [STD 1-12.28], (February 7, 1983).
• Portable Belt Sanding Machines as Covered by 29 CFR 1910.243(a)(3) and 29 CFR 1926.304(f). STD 01-13-004 [STD 1-13.4], (August 5, 1981).
• Applicable Standards As They Pertain to Iron Workers and Mechanical Power Presses. STD 01-12-027 [STD 1-12.27], (June 30, 1981).
• Clarification and Interpretation of 29 CFR 1910.217, Mechanical Power Press, as Applies to the Safeguarding. STD 01-12-024 [STD 1-12.24], (July 30, 1979).
• 29 CFR 1910.212(a)(3)(ii) Point of Operation Guarding for All Machines as Applied to the Hand-Fed Engraving Presses Used ... STD 01-12-022 [STD 1-12.22], (January 2, 1979).
• Defining Acceptable Guarding of Fan Blades. STD 01-12-001 [STD 1-12.1], (October 30, 1978).
• Caution Labeling of Radial Saws: 29 CFR 1910.213(h)(5). STD 01-12-004 [STD 1-12.4], (October 30, 1978).
• Acceptable Guarding for Circular Meat Cutting Saws: 29 CFR Section 1910.212(a)(3)(ii). STD 01-12-005 [STD 1-12.5], (October 30, 1978).
• 29 CFR 1910.218 Forging Machines. STD 01-12-006 [STD 1-12.6], (October 30, 1978).
• 29 CFR 1910.217 and 29 CFR 1910.212; Applicability of Platen Presses. STD 01-12-007 [STD 1-12.7], (October 30, 1978).
• 29 CFR 1910.215(a)(4), Abrasive Wheel Machinery Work Rests. STD 01-12-008 [STD 1-12.8], (October 30, 1978).
• Application of 29 CFR 1910.212(a)(1) to Food Waste Disposal Equipment. STD 01-12-010 [STD 1-12.10], (October 30, 1978).
• Clarification of 29 CFR 1910.219, the Terms "Enclosed" and "Fully Enclosed", as applying to Power Transmission Belts. STD 01-12-014 [STD 1-12.14], (October 30, 1978).
• 29 CFR 1910.213(a)(4), Woodworking Machinery Requirements. STD 01-12-015 [STD 1-12.15], (October 30, 1978).
• 29 CFR 1910.213(h)(1), Radial Saw Guards. STD 01-12-017 [STD 1-12.17], (October 30, 1978).
• 29 CFR 1910.213(c)(l) and (h)(1), Woodworking Machinery Guarding Requirements. STD 01-12-018 [STD 1-12.18], (October 30, 1978).
• Application 1910.212(a)(1) to Sewing Machines in the Light Apparel Manufacturing Industries. STD 01-12-019 [STD 1-12.19], (October 30, 1978).
• 29 CFR 1910.217(b)(3)(i), Mechanical Power Presses Single Stroke Mechanism Requirements. STD 01-12-020 [STD 1-12.20], (October 30, 1978).
• 29 CFR 1910.217 Mechanical Power Presses, Clarifications. STD 01-12-021 [STD 1-12.21], (October 30, 1978).

The basic regulation, in Section 1910.212, states that any machine that creates a hazard must be safeguarded to protect the operator and other employees. OSHA can also cite violations by referencing other standards such as the ANSI (American National Standards Institute) B11 series. The following is a list of each ANSI B11 Series Standard available at the printing of this publication.

• Note: These are NOT OSHA regulations. However, they do provide guidance from their originating organizations related to worker protection.

* ANSI Standards for Turning Machines